Get rid of stubborn partition on USB drive | TechBuzz

- Advertisement -



You have found partitions on a USB hard drive or USB stick that you cannot delete using Disk Management. With these tips, it usually works anyway. The data is then gone, of course.

I just had a case like this again. There was a USB stick that I had used for Linux experiments. It was bootable and had an EFI partition. But now the stick should only be used as a storage medium, which is why the extra partitions bothered me.

Of course I have to go first Disk Management grabbed. But in this not all of the unwanted partitions could be deleted. So what next?

The solution consists in using the command line tool Diskpartthe use of which we have already described here.

- Advertisement -

Important: The Windows tool Diskpart is a real killer when it comes to removing partitions. If the wrong disk is selected when executing the erase command, this can have undesirable consequences. When using the tool, focus on what you’re doing, rather than double and triple verifying that you intend to do the right thing.

That’s how it’s done

Plug in the USB stick. To be on the safe side, remove other storage devices (SD cards, other sticks, connected smartphones, external hard drives).

Take a look inside Disk Management, which you z. B. with Windowstaste+R and typing from Diskmgmt.msc can start. The physical data carriers are listed in the lower part. Also pay attention to the drive size. In our example (an old Surface Pro 4) we have a “Disk 0” with 238.35 GB. This is the SSD on which the system is installed. This is easy to recognize because, among other things, the Windows drive C: is on it.

READ  Start Office in Safe Mode | Apps & Software | Computer!Total | TechBuzz
- Advertisement -

Below is Disk 1 listed as 57.84 GB. Because no other drives are connected, because the size is correct and because “removable disk” is written, this obviously has to be the USB stick. When this screenshot was taken, the unwanted partitions were already gone.

Screenshot of Disk Management
We don’t want to delete anything on data carrier 0, just data carrier 1, recognizable by its size: at almost 58 GB, it must be the USB stick
(Those: PCtipp.ch)

The diskpart part

Now click Starttap cmd and dial at the command prompt the point Execute as administrator.

tap diskpart in and press Enter. This will start Diskpart. You can tell that you are in Diskpart mode by the fact that the prompt changes from C:\> to DISKPART> changes.

- Advertisement -

Provide overview: tap list disk in and press Enter. This will list the disks. This is the same information as in Disk Management, see screenshot (A). In our example, data medium 1 is the approx. 57 GB small USB stick.

Screenshot diskpart in command prompt
With list disk you list the physical drives, with select disk (and the number) you select the one to be treated, list partition lists the partitions there and with clean they are all removed immediately
(Those: PCtipp.ch)

Choose the right drive: If the drive to be emptied is here as Disk 1 appears, tap select disk 1 in and press Enter, see (B). This ensures that the erase command really applies to this physical drive.

List partitions: This isn’t necessary, because you’re going to clear them all together, but it doesn’t hurt to list again what should be deleted. You do this with list partition (Enter to press).

READ  Oh, Everything's Going to Hell on Star Trek: Picard | TechBuzz

The mini-partitions that we want to eliminate appear here – in the screenshot at (C)

Clear all: tap clean in and press Enter, the message «The disk has been cleaned» appears, see (D). Now if you again list partition Diskpart will tell you that there are no partitions on this disk (E).

Or just delete one? We described this in the other article. So here only briefly: The with list partition listed partitions are also numbered. With select partition 1 you can select the partition to be deleted (if the one with 1 is the one to be deleted), then with delete partition Clear.

You are done. To exit Diskpart, tap exit in and press Enter. To close the command prompt, you can also use the exit-Use command. Now you can create a partition on the USB stick again according to your wishes in the disk management.



Source link

- Advertisement -
Admin
Adminhttp://techbuzz.asia
I am admin of techbuzz.asia blog & I provide tech-related news. As a part of my hobby, I make content related to technology and gadgets reviews too. I love to be a content creator apart from it, I am a full-time employee in an MNC company and manage blogs systematically. You can mail me at [email protected]

More from author

Related posts

Advertisment

Latest posts

Currently free of charge instead of 2.99 euros: iPhone app gets better and better with age | TechBuzz

We're getting older every day and this iPhone app documents the whole truth in an impressive way. Because with the Dayli app you...

More important than the Xiaomi 12 Ultra: You’ve been waiting for this cell phone for too long | TechBuzz

Xiaomi has only introduced the Xiaomi 12 and 12 Pro so far. There was no 12 Ultra or 12 Lite, although the two...

Want to stay up to date with the latest news?

We would love to hear from you! Please fill in your details and we will stay in touch. It's that simple!